A basement floods. A house fire is put out. A lightning strike or power surge knocks out half the electronics in the office. Once everyone is safe, the next question is often: what about the data?

Drives damaged by water, fire or a power surge look hopeless, but they’re often more recoverable than people expect. The data is stored on platters or memory chips that can survive damage that destroys everything around them. What you do in the first days after the event makes the biggest difference.

Safety first

  • Don’t go into flooded areas or touch equipment that may still be connected to power.
  • Don’t enter a fire-damaged building until it’s been declared safe.
  • Take photos of damaged computers, servers and drives before you move them. Your insurance company may ask for them.

The rule for all three: don’t power it on

This is the most important step, and the hardest one to follow. A wet, smoke-damaged or surge-hit device can look fine. Turning it on to check can short its electronics, spin water or soot across the platters, or finish off a component that was only partly damaged.

Unplug everything. Don’t try “just one more time” in another computer.

Flood-damaged drives

Water itself is not what destroys data. The problem is what’s in the water and what happens as it dries: minerals, mud and chemicals left behind on circuit boards and inside drives, and corrosion that keeps spreading for days.

  • Don’t dry drives with heat. No hair dryers, ovens, heaters or sunlight.
  • Don’t shake them or try to drain them.
  • Don’t open the drive to let it air out. Hard drives are sealed for a reason, and opening one outside a lab can scratch the platters.
  • Put each wet drive in a sealed plastic bag and get it to a lab as soon as you can. If the water was muddy or salty, keeping the drive from drying out before cleaning can make recovery easier.
  • Laptops and phones: power them off, don’t charge them, and don’t use rice. Read 9 Data Recovery “Hacks” That Make Things Worse for why.

Fire- and heat-damaged drives

A drive can be damaged by fire without ever touching a flame. Heat can warp parts, and smoke leaves soot that is both corrosive and abrasive. Water from firefighting often adds water damage on top.

  • Don’t wipe off soot or try to clean the drive or its circuit board.
  • Handle drives by the edges and as little as possible.
  • Bag each drive separately to keep soot from spreading, and keep them away from more heat.
  • Melted or blackened cases aren’t the end. The platters inside are often intact even when the outside looks destroyed.

Power surge and lightning damage

Surges usually hit the electronics, not the stored data. On a hard drive, the circuit board often fails while the platters and heads are untouched. On SSDs and flash drives, the controller or power components can fail while the memory chips survive.

  • Signs of surge damage: the drive is dead and silent, isn’t detected at all, or there’s a burnt smell from the computer or drive.
  • Don’t swap the circuit board with one from another drive. Modern drives store unique calibration data on their own board, so a swap rarely works and can cause more damage.
  • Don’t keep plugging the drive into different computers or USB docks. If a component has shorted, power can do more damage each time.

Servers and RAID after a disaster

If a server or storage system was affected, the steps above apply to every drive in it, plus a few more:

  • Label each drive with its slot number before removing anything.
  • Don’t let the system rebuild or initialize the array when power comes back.
  • Don’t replace drives one by one to “see which ones work.”

Read RAID Failure: What to Do First for more, and see our RAID data recovery page.

What can usually be recovered

Every case is different, and some media is too badly damaged. But in many flood, fire and surge cases, the parts that hold the data, the platters in a hard drive or the memory chips in an SSD, phone or memory card, survive. With the right cleaning, repair and specialized equipment, that data can often be read. The less a damaged drive has been powered on or handled since the event, the better the chances.

Disklab recovers data from hard drives, SSDs and flash media, phones and RAID systems, including devices damaged by water, fire and power surges.

Disklab is a data recovery lab in St. Louis, on Olive Blvd. You can drop off your device or ship it to us from anywhere in the US.

Start a recovery case or call us at 1-844-347-5522. The evaluation is free, and you pay only if we recover your data.